LED tube lights presumably for the average person is very familiar with the term, especially with the recent uproar nuclear issue be discussed at the same time, people began to think about other sources of energy and how to save power.
Only 18 watts of lighting wattage LED tube light is developed by the hourly consumption of 40 watts fluorescent tubes in general terms, the number of watts consumed per hour in less than 22 W lost relative degrees on both electricity and save more than half.
Many people must have pondered why LED tube lights are so long and life saving, but the penetration rate is still low in the market. In fact, the main reason is still in the research and development of LED tube lights on the manufacturing costs are higher than many of the traditional lamp, but there is an important factor is that the general LED tube lights can not be installed on the traditional lamps, LED tube lights to replace the past must change lighting or changed wire configuration, in addition to the original waste outside the socket, the installation is relatively time consuming, and if the change increases the risk of the wire. The lighting fixture is designed to replace the original without changing the traditional model, in addition to the installation more convenient, but also reduces the number of installation costs.
Li lit LED illumination lamps launched patented power module built- in solid state components composed of non-electrolytic capacitor design, life and LED similar to effectively improve the efficiency and life of the LED light source. Taiwan LED using well-known brands of grain, high efficiency and no UV light, protecting eye health and life of more than 50,000 hours.
Sunday, December 29, 2013
Thursday, December 26, 2013
LED bicycle lights that allow you to drive more safely
Although bicycling is not now a couple of years ago so popular, but now the bike lane, but do more than have a lot to improve before. Ah, but now the weather is really hot during the day if we do not want to ride, then ride a bicycle at night might come to it. But of course we should pay more attention to the evening ride safety Hello. So light, but very important to Afghanistan. Not only to protect themselves but also to protect others.
Today we introduce rather special lights. Although he is LED, with the average LED bicycle lights are very different, not only the brightness of it. Although also a LUMIGRIDS LED bicycle lights, but at night is not a beam of light projected out.
Yes as you can see in the figure the same, a lot of plaid, what is the use of this lattice? Usually ride in the evening when everyone is not too easy to distinguish the ground is flat is concave, especially on the road at every turn on a water hole or manhole cover the like, which may increase the risk when riding. With LUMIGRIDS LED can clearly see where the uneven ground Hello. Simply will LUMIGRIDS LED mounted on the faucet, you can use it.
As a rider is not safe at night much, LUMIGRIDS LED also introduced three versions of different sizes to be used in different places, the normal mode 140X180mm, high-speed mode 140x260mm, team mode 300x200mm. This is really a good invention.
 |
| LED bicycle lights |
Yes as you can see in the figure the same, a lot of plaid, what is the use of this lattice? Usually ride in the evening when everyone is not too easy to distinguish the ground is flat is concave, especially on the road at every turn on a water hole or manhole cover the like, which may increase the risk when riding. With LUMIGRIDS LED can clearly see where the uneven ground Hello. Simply will LUMIGRIDS LED mounted on the faucet, you can use it.
As a rider is not safe at night much, LUMIGRIDS LED also introduced three versions of different sizes to be used in different places, the normal mode 140X180mm, high-speed mode 140x260mm, team mode 300x200mm. This is really a good invention.
Wednesday, December 25, 2013
Magical LED bicycle lights on the bicycle wheels
A company in Northern California is the bike to a new level, by using LED bicycle lights illuminates the wheel, bicycle wheel capable of rendering custom images and animations. Bike wheel Monkey Lectric's Monkey LightPro system when cycling the LED displays, Monkey LightPro is a set of four lines of waterproof LED light strip. In the web -based software you can program custom images and animations can be sent to the optical system via Bluetooth.
When the speed reaches 10-40 mile bike, mounted on a bicycle wheel Monkey LightPro system will make the LED bicycle lights up. Since we know the "persistence of vision" effect, these flashes of light in the human vision will be showing a recognizable image, we can see the animation.
Bike lights are installed on the bike for night riding friends ride lamps. Currently riding a friendly multi-purpose flashlight plus holding clip this combination to serve as night riding equipment, the biggest advantage is that the economy portable floodlight drawback is narrow, the big blind, short battery life, poor security. For professional riding friends, they are equipped with professional bicycle lights; bicycle lamps of this type have a long life, long-range floodlight, waterproof tube and sweat, carry bumps and high safety index, but its expensive cost Friends also prohibitive for ordinary ride.
Currently bike lights can be divided into self-generating -and battery-powered two types of bicycle lights, and self-generation type can be divided into two types of tire friction generation and power generation hub built- generator type ; battery-powered bike lights can be divided into cells and separate lights and battery with a light body. Since the power -type bicycle lights because the lights are not required to bear the occasion also need friction resistance, which for the most demanding riding friends; this is unacceptable, so the current is more commonly used in battery-powered bike lights.
When the speed reaches 10-40 mile bike, mounted on a bicycle wheel Monkey LightPro system will make the LED bicycle lights up. Since we know the "persistence of vision" effect, these flashes of light in the human vision will be showing a recognizable image, we can see the animation.
Bike lights are installed on the bike for night riding friends ride lamps. Currently riding a friendly multi-purpose flashlight plus holding clip this combination to serve as night riding equipment, the biggest advantage is that the economy portable floodlight drawback is narrow, the big blind, short battery life, poor security. For professional riding friends, they are equipped with professional bicycle lights; bicycle lamps of this type have a long life, long-range floodlight, waterproof tube and sweat, carry bumps and high safety index, but its expensive cost Friends also prohibitive for ordinary ride.
Currently bike lights can be divided into self-generating -and battery-powered two types of bicycle lights, and self-generation type can be divided into two types of tire friction generation and power generation hub built- generator type ; battery-powered bike lights can be divided into cells and separate lights and battery with a light body. Since the power -type bicycle lights because the lights are not required to bear the occasion also need friction resistance, which for the most demanding riding friends; this is unacceptable, so the current is more commonly used in battery-powered bike lights.
Tuesday, December 24, 2013
How to effectively install your LED bicycle lights
For the installation of LED bicycle lights, is left to go, or right away, very different! Whether headlights or taillights, common installation location bicycle is at the center axis of the front and rear of the car.
LED bicycle lights, headlights or taillights both common installation locations are at the center axis of the front and rear of the car. For example: a handle mounted on the central headlamp ( or close to the center position) in front of the head pipe, or the top of the front fork ; Tail pipe mounted seat cushion bag, or the shelf ; these are basically mounted in the center axis of the bicycle on.
If not, I go left or right to go there a relationship! China, the United States, Europe, and most of the countries in the world are relying on the right side of the road vehicle travel, but like the United Kingdom, Ireland, Japan, Hong Kong, and Singapore, it is the road on the left. Due to the design of public roads are cars to go inside track, bike path to go outside ; time for safety effect, to set the high quality safety lights mounted on one side of the bike around, it is recommended to consider mounted on the inside of the side by the road.
In China, it is mounted on the left side of the bike. When riding a bicycle in China, the steam locomotive is on the left side of the bicycle, lamps mounted on the left, for example, the left fork or fork left rear, mounted on the right side than on the steam locomotive drivers produce better warning effect.
If it is left to go in the country, such as Japan, the situation is just the opposite. This is why we see some Japanese brand car city car or parent, if the original mill with electric headlights so, many of which are mounted on the right fork of the reasons.
LED bicycle lights, headlights or taillights both common installation locations are at the center axis of the front and rear of the car. For example: a handle mounted on the central headlamp ( or close to the center position) in front of the head pipe, or the top of the front fork ; Tail pipe mounted seat cushion bag, or the shelf ; these are basically mounted in the center axis of the bicycle on.
If not, I go left or right to go there a relationship! China, the United States, Europe, and most of the countries in the world are relying on the right side of the road vehicle travel, but like the United Kingdom, Ireland, Japan, Hong Kong, and Singapore, it is the road on the left. Due to the design of public roads are cars to go inside track, bike path to go outside ; time for safety effect, to set the high quality safety lights mounted on one side of the bike around, it is recommended to consider mounted on the inside of the side by the road.
In China, it is mounted on the left side of the bike. When riding a bicycle in China, the steam locomotive is on the left side of the bicycle, lamps mounted on the left, for example, the left fork or fork left rear, mounted on the right side than on the steam locomotive drivers produce better warning effect.
If it is left to go in the country, such as Japan, the situation is just the opposite. This is why we see some Japanese brand car city car or parent, if the original mill with electric headlights so, many of which are mounted on the right fork of the reasons.
Monday, December 23, 2013
Innovative laser projection LED bicycle lights
According to British network, a British university graduate has invented a new type of bike lights, which can image projected onto a road bike, the road to alert the driver.
LED bicycle lights inventor Emily Brooke studied product design at the University of Brighton. She said he hoped this invention can reduce traffic accidents.
27 -year-old Emily from Bath, in contact with the bus companies, road safety experts and local authorities inspired her.
The invention named Blaze. It uses a laser distance bike in the street in front of the projection of five meters out green LED bicycle lights, thereby eliminating blind spots.
Emily said she had attended a charity organization cycling thought of this idea.
"I was still learning product design, I do graduate work is about urban bike, " she said.
"As part of this design, I studied the relevant data bicycle accident when I rode a bicycle around the Brighton time will think that bus or truck can not see me."
Currently she designed LED bicycle lights cost £ 60. Flashing lights intermittent and continuous illumination modes.
Last year, Emily graduated from the University of Brighton, after obtaining Babson College in Massachusetts, USA (Babson College) entrepreneur scholarships to continue their studies.
In product development, it is precisely at this stage, the birth of a landmark new product --- artillery batteries bike lights.
At that time, most of the lights used on the bike are a candle or oil lamp type style, and when the wind blows it is easy to put out, very inconvenient. Although there are battery-operated lights, but life expectancy is only two to three hours, and very prone to failure, not practical. Therefore, Konosuke keen on design determined to make improvements on the battery type lights.
Thus, Konosuke spent half a year, making dozens of samples, the results can be achieved lighting thirty to forty hours, and innovative style.
However, such an epoch-making product, but no one is willing to underwrite wholesalers. "Take 10000 divergent out, there are always repercussions of it," Konosuke well prepared backs against the wall. Accordance with the prevailing price, these bulbs equivalent to the level of 10,000 yen 5, 6,000, if unsuccessful, workshops will face closure. And this marketing approach can be described as a landmark initiative.
It carries the ultimate fate of the company's real propaganda success, to appreciate the true value of retail products continue to place orders, after two or three months, it reached the level of monthly sales of 2,000.
LED bicycle lights inventor Emily Brooke studied product design at the University of Brighton. She said he hoped this invention can reduce traffic accidents.
27 -year-old Emily from Bath, in contact with the bus companies, road safety experts and local authorities inspired her.
The invention named Blaze. It uses a laser distance bike in the street in front of the projection of five meters out green LED bicycle lights, thereby eliminating blind spots.
Emily said she had attended a charity organization cycling thought of this idea.
"I was still learning product design, I do graduate work is about urban bike, " she said.
"As part of this design, I studied the relevant data bicycle accident when I rode a bicycle around the Brighton time will think that bus or truck can not see me."
Currently she designed LED bicycle lights cost £ 60. Flashing lights intermittent and continuous illumination modes.
Last year, Emily graduated from the University of Brighton, after obtaining Babson College in Massachusetts, USA (Babson College) entrepreneur scholarships to continue their studies.
In product development, it is precisely at this stage, the birth of a landmark new product --- artillery batteries bike lights.
At that time, most of the lights used on the bike are a candle or oil lamp type style, and when the wind blows it is easy to put out, very inconvenient. Although there are battery-operated lights, but life expectancy is only two to three hours, and very prone to failure, not practical. Therefore, Konosuke keen on design determined to make improvements on the battery type lights.
Thus, Konosuke spent half a year, making dozens of samples, the results can be achieved lighting thirty to forty hours, and innovative style.
However, such an epoch-making product, but no one is willing to underwrite wholesalers. "Take 10000 divergent out, there are always repercussions of it," Konosuke well prepared backs against the wall. Accordance with the prevailing price, these bulbs equivalent to the level of 10,000 yen 5, 6,000, if unsuccessful, workshops will face closure. And this marketing approach can be described as a landmark initiative.
It carries the ultimate fate of the company's real propaganda success, to appreciate the true value of retail products continue to place orders, after two or three months, it reached the level of monthly sales of 2,000.
Sunday, December 22, 2013
LED tube lights are expected to exceed two percent of global market share in 2016
LED manufacturers are actively increasing the output of LED lighting products, which this year has just launched a product LED fluorescent tube, has been a wide range of output. According to NPD Display Search latest report (LED Lighting Market and Forecast Report), LED tube light 2013's international market share will reach 6 %, and will rise in 2016 to 22.3 %. FL lamp output of 200 million in 2013 to $ 30 million, the 2016 is expected to increase to 700 million 9,100 million.
NPD Display Search LED analyst Steven said: "LED lighting provides innovative lighting, and effectively reduces energy consumption especially in the areas of power shortage, LED tube light will most likely be popular, and LED lighting equipment will be widely around the world. Applications, " in Japan, the United States and Europe continue to increase the output of LED tube lights; newborns as the market, LED is clearly not the consumer's first choice, but the market is still growing for the following reasons:
LED tube lights are considered a green product because it does not use mercury in the manufacturing process.
LED tube lights can be saving 50%, power factor between 0.9-0.99 while T8FL lamp is only 0.7.
LED tube light life longer than T8FL lamp is expected to be 5 years or 30,000 hours.
LED tube light is ideal for replacing old-fashioned lamps are used in the office or in the basement, because these areas often need 24 hours lights, energy saving is essential.
In the technical part, although the issue before the LED tube lights has a greater radiation on the angle and color quality has been resolved. However, challenges remain, especially the problem of high cost, which has become a problem to the promotion of a vintage lamp LED tube light alternatives faced during the first, because, after all, old-fashioned lamp lower prices.
LED manufacturers are trying to reduce costs through design and to narrow the price difference between the two. One way is to design a product suitable for most LED lighting power supply modules. In 2013, some of the power module manufacturers to design a new product to the MR-16, A-Lamp and LED tube lights and other types of use, making the cost of these products decreased by 10%.
Steven added: "The market has introduced a number of different types of LED tube lights, including different shapes, rated power, length, color and lighting features, but due to the lack of standard specifications, the consumer is difficult to accurately select the most suited to their needs. The product, which is also the problem of LED tube lights to promote the process of encounter. "
NPD Display Search LED analyst Steven said: "LED lighting provides innovative lighting, and effectively reduces energy consumption especially in the areas of power shortage, LED tube light will most likely be popular, and LED lighting equipment will be widely around the world. Applications, " in Japan, the United States and Europe continue to increase the output of LED tube lights; newborns as the market, LED is clearly not the consumer's first choice, but the market is still growing for the following reasons:
LED tube lights are considered a green product because it does not use mercury in the manufacturing process.
LED tube lights can be saving 50%, power factor between 0.9-0.99 while T8FL lamp is only 0.7.
LED tube light life longer than T8FL lamp is expected to be 5 years or 30,000 hours.
LED tube light is ideal for replacing old-fashioned lamps are used in the office or in the basement, because these areas often need 24 hours lights, energy saving is essential.
In the technical part, although the issue before the LED tube lights has a greater radiation on the angle and color quality has been resolved. However, challenges remain, especially the problem of high cost, which has become a problem to the promotion of a vintage lamp LED tube light alternatives faced during the first, because, after all, old-fashioned lamp lower prices.
LED manufacturers are trying to reduce costs through design and to narrow the price difference between the two. One way is to design a product suitable for most LED lighting power supply modules. In 2013, some of the power module manufacturers to design a new product to the MR-16, A-Lamp and LED tube lights and other types of use, making the cost of these products decreased by 10%.
Steven added: "The market has introduced a number of different types of LED tube lights, including different shapes, rated power, length, color and lighting features, but due to the lack of standard specifications, the consumer is difficult to accurately select the most suited to their needs. The product, which is also the problem of LED tube lights to promote the process of encounter. "
Thursday, December 19, 2013
British student invents Batman LED bicycle lights that can reduce the risk of danger
British Daily Mail reported recently a British university student has developed a new type of life-saving LED bicycle lights, which can project a bright laser images similar to Batman to remind other motor vehicle driver's attention to their existence.
The design by the British university student Emily Brooke lightweight, battery-powered device is called BLAZE, it is attached to the handlebar, and the bike can travel on the road in front of 20 feet (6.1 meters) of the projected image of the green. Such bright bike bicycle traveling in front of the image is located, to remind others and reduce the risk of motor vehicle drivers entering the bike path.
According to the British Ministry of Transportation Statistics, died in traffic accidents last year, 79% of cyclists are moving forward when they were hit from the vehicle to. Brook and road safety experts from the United Kingdom Bath, Brighton and Hove City Council, Brighton and Hove Bus Company vehicle driving psychologists work together to develop this bike is also visible in the daytime LED bicycle lights.
Brooke has made this concept in the final year of the University of Brighton, UK product design course, she felt that this is a very simple concept, but it greatly improves the security on the road cyclists. "I hope that by increasing the visibility of the bicycle, trail and awareness of the existence of the ultimate people on bikes, road bikes and dealing with the city's security problems."
"80% of bicycle accidents have occurred in the bike straight, and other motor vehicles hitting them. Reasons for the occurrence of such accidents is the main driver of the vehicle did not see from the vehicle in the city roads, bicycles are often easily overlooked. " " Even a bicycle at night like a Christmas tree and bright, but in the blind spot of the bus the bus they are still difficult to see. Use BLAZE, you can see cyclists traveling in front of the bike logo, I believe the threat of cyclists in the road of life safety, it can play an important role. "
The design by the British university student Emily Brooke lightweight, battery-powered device is called BLAZE, it is attached to the handlebar, and the bike can travel on the road in front of 20 feet (6.1 meters) of the projected image of the green. Such bright bike bicycle traveling in front of the image is located, to remind others and reduce the risk of motor vehicle drivers entering the bike path.
According to the British Ministry of Transportation Statistics, died in traffic accidents last year, 79% of cyclists are moving forward when they were hit from the vehicle to. Brook and road safety experts from the United Kingdom Bath, Brighton and Hove City Council, Brighton and Hove Bus Company vehicle driving psychologists work together to develop this bike is also visible in the daytime LED bicycle lights.
Brooke has made this concept in the final year of the University of Brighton, UK product design course, she felt that this is a very simple concept, but it greatly improves the security on the road cyclists. "I hope that by increasing the visibility of the bicycle, trail and awareness of the existence of the ultimate people on bikes, road bikes and dealing with the city's security problems."
"80% of bicycle accidents have occurred in the bike straight, and other motor vehicles hitting them. Reasons for the occurrence of such accidents is the main driver of the vehicle did not see from the vehicle in the city roads, bicycles are often easily overlooked. " " Even a bicycle at night like a Christmas tree and bright, but in the blind spot of the bus the bus they are still difficult to see. Use BLAZE, you can see cyclists traveling in front of the bike logo, I believe the threat of cyclists in the road of life safety, it can play an important role. "
Wednesday, December 18, 2013
Power Integrations introduced new LED T8 fluorescent lighting driver design
For energy-efficient power conversion industry leader in high-voltage integrated circuits Power Integrations, Inc. released two applications for T8 fluorescent lightings to replace high-efficiency, non-isolated, high power factor (PF) today LED driver reference design.
The new design is characterized by the use of a few components and simple core materials and single-sided circuit board design, the power density of the industry's leading 14.2W/in3 level. LED Driver Design from Power Integrations based on the Link Switch-PL Series IC devices LNK460KG, DER-337 (high voltage input) and DER-345 (low- input) in a detailed circuit description. Both drives are using a single-stage, non-isolated topology, and the drive behind the thickness of only 8mm- sufficient LED T8 fluorescent lighting installed.
Buck - Boost (DER-337) or buck (DER-345) is configured to provide more than 0.9 power factor and low THD, to meet EN61000-3-2C limits. This is designed to meet EMI standards, easily meet EN55015 (EMI) Class B specifications. The integrated single-stage driver IC can control the PFC and constant current output, so that the number of components is less than 30 designs. Both drives efficiency up to 92 %, respectively (DER-337) and 89% (DER-345), the output power are 20W (output voltage 85V, output current is 240mA).
Power Integrations Andrew Smith product marketing manager, said: "LED lamp market is moving to a non-isolated drive because this drive can improve system efficiency, while reducing the temperature of the drive components and the number of components used in these boards about isolated. Half of the design, and the efficiency of 3-4 % is usually higher than the latter because of a high PF and low THD, they are very suitable for ubiquitous commercial and industrial lighting applications. "
Power Integrations, Inc. provides high-voltage integrated circuits for energy-efficient components and other high-voltage power conversion provider, headquartered in Silicon Valley. The company 's innovative technology that can help include TV, PC, home appliances, smart meters and LED lights, including a large number of electronic products designed compact, reliable AC-DC power supply.
The new design is characterized by the use of a few components and simple core materials and single-sided circuit board design, the power density of the industry's leading 14.2W/in3 level. LED Driver Design from Power Integrations based on the Link Switch-PL Series IC devices LNK460KG, DER-337 (high voltage input) and DER-345 (low- input) in a detailed circuit description. Both drives are using a single-stage, non-isolated topology, and the drive behind the thickness of only 8mm- sufficient LED T8 fluorescent lighting installed.
Buck - Boost (DER-337) or buck (DER-345) is configured to provide more than 0.9 power factor and low THD, to meet EN61000-3-2C limits. This is designed to meet EMI standards, easily meet EN55015 (EMI) Class B specifications. The integrated single-stage driver IC can control the PFC and constant current output, so that the number of components is less than 30 designs. Both drives efficiency up to 92 %, respectively (DER-337) and 89% (DER-345), the output power are 20W (output voltage 85V, output current is 240mA).
Power Integrations Andrew Smith product marketing manager, said: "LED lamp market is moving to a non-isolated drive because this drive can improve system efficiency, while reducing the temperature of the drive components and the number of components used in these boards about isolated. Half of the design, and the efficiency of 3-4 % is usually higher than the latter because of a high PF and low THD, they are very suitable for ubiquitous commercial and industrial lighting applications. "
Power Integrations, Inc. provides high-voltage integrated circuits for energy-efficient components and other high-voltage power conversion provider, headquartered in Silicon Valley. The company 's innovative technology that can help include TV, PC, home appliances, smart meters and LED lights, including a large number of electronic products designed compact, reliable AC-DC power supply.
Tuesday, December 17, 2013
How to balance the supply and demand of waterproof tube
Strip surface to do with drops of clear water "epoxy glue" and set "waterproof tube" in two ways. It can also be made directly without processing products. 3mm, 5mm, 6mm, 10mm, etc. for customers to choose, can also be customized (lights for 08050603ed SMD LED beads with lights ) Standard Size: 34 light / m 20 light / m 17 light / m 9 light / m.
Waterproof tube can be arbitrary bending deformation; the product does not appear dead lights after repeated bending and kneading, transparent plastic and FFC / FPC separation and transparent plastic to break other bad billing, the technology leader in the industry.
There are a variety of styles for selection, customers can stickers or screen printing on the battery compartment. Battery life at 25 ED status lights lit up to 30 hours, replace the batteries is also very convenient. 3mm --- 10 mm. Strip lengths can be based on customer requirements. Light bar can be cut according to the different needs of customers.
Instructions for use:
A. The product can be pasted, fixed on the binding. First adhesive surface, oil, debris cleaned, coated with adhesive glue adhesive surface, making it a solid combination.
B. For the convenience of customers using the product, providing unilateral and bilateral skirts tube skirts pipe casing can be sewn, fixed suture location, you can use the needle and suture the product wrapping cloth, clothing, textiles, and leather and so on.
C. The product can be inlaid way easily fixed in the gap can be outside of this product for ED lights, set in a small gap, so that fixed.
Scope:
Apply to pet collars, pull belt, leash, work card lanyards, lanyard, light frames and other light products.
Applicable to all kinds of fashion handmade works of art, all kinds of bags, shoes, fashion sling, so that your products are selling more
It is suitable for car beauty and decorating, since the role of the security alert.
For a variety of LED advertising signs, fine decorative indoor and outdoor advertising display boards.
Applicable to the store, bridge, tunnel, and path and contour signs lighting project
It is suitable for creative gifts, electronic toys, home decorations, business and advertising gifts, handicrafts, health technology gifts, travel and sports products, DIY personalized gifts, new exotic products, household goods (furniture cove trim, ceiling, door frames, wine, wardrobe, and TV cabinet), textile gifts.
Waterproof tube can be arbitrary bending deformation; the product does not appear dead lights after repeated bending and kneading, transparent plastic and FFC / FPC separation and transparent plastic to break other bad billing, the technology leader in the industry.
There are a variety of styles for selection, customers can stickers or screen printing on the battery compartment. Battery life at 25 ED status lights lit up to 30 hours, replace the batteries is also very convenient. 3mm --- 10 mm. Strip lengths can be based on customer requirements. Light bar can be cut according to the different needs of customers.
Instructions for use:
A. The product can be pasted, fixed on the binding. First adhesive surface, oil, debris cleaned, coated with adhesive glue adhesive surface, making it a solid combination.
B. For the convenience of customers using the product, providing unilateral and bilateral skirts tube skirts pipe casing can be sewn, fixed suture location, you can use the needle and suture the product wrapping cloth, clothing, textiles, and leather and so on.
C. The product can be inlaid way easily fixed in the gap can be outside of this product for ED lights, set in a small gap, so that fixed.
Scope:
Apply to pet collars, pull belt, leash, work card lanyards, lanyard, light frames and other light products.
Applicable to all kinds of fashion handmade works of art, all kinds of bags, shoes, fashion sling, so that your products are selling more
It is suitable for car beauty and decorating, since the role of the security alert.
For a variety of LED advertising signs, fine decorative indoor and outdoor advertising display boards.
Applicable to the store, bridge, tunnel, and path and contour signs lighting project
It is suitable for creative gifts, electronic toys, home decorations, business and advertising gifts, handicrafts, health technology gifts, travel and sports products, DIY personalized gifts, new exotic products, household goods (furniture cove trim, ceiling, door frames, wine, wardrobe, and TV cabinet), textile gifts.
Monday, December 16, 2013
The new Low power green laser disco light creates amazing lighting performance
HC audio and lighting network reported an increase in the global population as well as the advancement of technology, the energy consumption rate becomes faster and faster. Now the "energy " and " sustainable development" has become a worldwide issue. This article will explore the concept of a product - that is stylishly designed light a lamp, which uses a passive cooling and blue laser technology, making consumes less than 1 watt of power, will be able to illuminate your world.
Since the green laser disco light was invented in the nineteenth century, has been a hundred years. During the rapid development of new technologies, but very important in our daily life lighting equipment, its principles and techniques have not been much of a leap.
Since we expect to enter the full twenty-first century so far, twelve years have passed. We are in urgent need of a lighting device of this new century. The new lighting system to be introduced in this article called Firefly, which is a revolutionary lighting. Firefly use new technology is very different from the conventional techniques common in the lighting.
The new lighting fixture uses a laser, and unlike traditional lighting devices as the light guide material wrapped around the light source (such as LED, or a conventional filament, etc.) to dissipate the light. The light emitted by the laser is "off" very far, and can maintain its brightness. Users simply place this product where lighting is required, the rest of the things it yourself: the light. Since we no longer have the old-fashioned lamp, and do not worry about wasting energy. As the product is used in a passive cooling system, so it does not contain any internal moving parts, thus eliminating the noise.
This product is very environmentally friendly; the material recovery rate reached 99.6 percent, while its power is surprisingly less than 1 watt. This advantage makes this green laser disco light Firefly deserved to be environmentally friendly energy-saving lamps king.
Firefly to people's home or on the road lighting provides a new experience and choice. The use of portable lamps emit hundreds of Blu-ray green laser disco light, as there are countless fireflies linger around you generally illuminate the surroundings.
Use the supplied adapter, the lamps can be plugged into any standard outlet, place it in your own home or work place. Four-way divergence of the laser beam through the darkness to illuminate houses, making the illuminated region produces dreamy effect.
Not only that, the Blu-ray Firefly can also be used for outdoor activities, such as outing, camping and the like. At this point, you only need two AAA batteries can be used to carry Firefly. If you need long-term use in the outdoors, four batteries can guarantee a long period of lighting up. With this fixture, you will be able to decorate your camping trip as if fantasy wonderland generally wonderful story.
Since the green laser disco light was invented in the nineteenth century, has been a hundred years. During the rapid development of new technologies, but very important in our daily life lighting equipment, its principles and techniques have not been much of a leap.
Since we expect to enter the full twenty-first century so far, twelve years have passed. We are in urgent need of a lighting device of this new century. The new lighting system to be introduced in this article called Firefly, which is a revolutionary lighting. Firefly use new technology is very different from the conventional techniques common in the lighting.
The new lighting fixture uses a laser, and unlike traditional lighting devices as the light guide material wrapped around the light source (such as LED, or a conventional filament, etc.) to dissipate the light. The light emitted by the laser is "off" very far, and can maintain its brightness. Users simply place this product where lighting is required, the rest of the things it yourself: the light. Since we no longer have the old-fashioned lamp, and do not worry about wasting energy. As the product is used in a passive cooling system, so it does not contain any internal moving parts, thus eliminating the noise.
This product is very environmentally friendly; the material recovery rate reached 99.6 percent, while its power is surprisingly less than 1 watt. This advantage makes this green laser disco light Firefly deserved to be environmentally friendly energy-saving lamps king.
Firefly to people's home or on the road lighting provides a new experience and choice. The use of portable lamps emit hundreds of Blu-ray green laser disco light, as there are countless fireflies linger around you generally illuminate the surroundings.
Use the supplied adapter, the lamps can be plugged into any standard outlet, place it in your own home or work place. Four-way divergence of the laser beam through the darkness to illuminate houses, making the illuminated region produces dreamy effect.
Not only that, the Blu-ray Firefly can also be used for outdoor activities, such as outing, camping and the like. At this point, you only need two AAA batteries can be used to carry Firefly. If you need long-term use in the outdoors, four batteries can guarantee a long period of lighting up. With this fixture, you will be able to decorate your camping trip as if fantasy wonderland generally wonderful story.
Wednesday, December 11, 2013
LuguLake Release New Wireless Bluetooth Stereo Headset V2.1
LuguLake Stereo Bluetooth Wireless Headphones feature hidden microphone Free yourself from cables for a better user experience, stereo Bluetooth function Conveniently located phone and music controls, soft ear pads and adjustable headband for extended wearing comfort, Built in Micro SD Card up to 32GB, Supports FM Radio,
Convenient all-in-one design for simplicity and functionality, Digital volume control, Talk hands-free on your phone. Hands-free calling / receiving for your mobile phone. It allows you to walk, run, play sports, and even dance to your favorite music while never missing an incoming call.
Connect LuguLake Bluetooth headphones with your iPad, iPhone, iPod, Android phones, Blackberry, MP3, Computer, Android tablets, and other Bluetooth enabled devices.You can play music of MP3 and WMA format through Micro-SD card (up to 32GB). Built-in onboard controls and integrated microphone make browsing your music library and hands-free calling a breeze! Rechargeable battery provides an incredible 6-8 hours of audio plackback! Noise reduction ensures clear conversations even in noisy environments.
It is compatible with: Various Bluetooth enabled devices, for example mobile phone, PDA, laptops, MP3/4/5 etc. NOT FOR Win 8. There is ON-OFF button on the side of device, please turn it on before using it. There is a yellow light when turn it on. Please press the "EQ" button for around 5-7 seconds, and then the red and yellow light will shine alternately. Then you can search "BT9001" on your bluetooth enabled device. And the pairing code is "0000" if you need
Attention:
1.This bluetooth headphone can not be connected with two devices simultaneously
2.The red indicator light is only a charging indicator, it may not go off or turn green when headphone is fully charged
3.First charging time should be 6 hours to activate the battery cell and only 4 hours is needed after that
4.The bluetooth and radio function will interchange automatically in the condition of lower battery
Convenient all-in-one design for simplicity and functionality, Digital volume control, Talk hands-free on your phone. Hands-free calling / receiving for your mobile phone. It allows you to walk, run, play sports, and even dance to your favorite music while never missing an incoming call.
Connect LuguLake Bluetooth headphones with your iPad, iPhone, iPod, Android phones, Blackberry, MP3, Computer, Android tablets, and other Bluetooth enabled devices.You can play music of MP3 and WMA format through Micro-SD card (up to 32GB). Built-in onboard controls and integrated microphone make browsing your music library and hands-free calling a breeze! Rechargeable battery provides an incredible 6-8 hours of audio plackback! Noise reduction ensures clear conversations even in noisy environments.
It is compatible with: Various Bluetooth enabled devices, for example mobile phone, PDA, laptops, MP3/4/5 etc. NOT FOR Win 8. There is ON-OFF button on the side of device, please turn it on before using it. There is a yellow light when turn it on. Please press the "EQ" button for around 5-7 seconds, and then the red and yellow light will shine alternately. Then you can search "BT9001" on your bluetooth enabled device. And the pairing code is "0000" if you need
Attention:
1.This bluetooth headphone can not be connected with two devices simultaneously
2.The red indicator light is only a charging indicator, it may not go off or turn green when headphone is fully charged
3.First charging time should be 6 hours to activate the battery cell and only 4 hours is needed after that
4.The bluetooth and radio function will interchange automatically in the condition of lower battery
Tuesday, December 10, 2013
What are some of the important applications of building light?
As we all know, the building is composed of the determinants of urban space, with light at night to shape the image of the building is a re-creation of the city beautiful.
Architecture and urban space groups combined in the night in the way people evaluate the merits of a direct impact on the urban night landscape. Administrative buildings, too, should the overall space requirements of urban night departure, considering the amount of body building, appearance, color, style, materials, textures and the surrounding environment and other factors, and then depending on the characteristics of the building, to select the focus on the performance of the site, using appropriate building light the way, with a reasonable light color, shape of the building for night performance.
Administrative buildings should be dignified, concise, simple lighting theme, generally should not use colored light, colored light irradiation topical use only low saturation when necessary. In addition to the exhibit building light morphological structure of the target, light and flexible application of direct investment, indirect investment in the transmittance of light or other means.
Common building light methods are cast lighting, the translucent lighting, decorative lighting and specialty lighting, often of two or more kinds of illumination combined.
This is the basic way of building light, lighting of the overall vote (floodlit) and local cast lighting. Is to cast light mounted on the outside of a building or buildings, a building or a part of the direct exposure of the building, remodeling and building image rendering building light the way at night. Often use metal halide light source, such as high pressure sodium and LED.
To determine a good part of the illuminated surface of each façade illumination and brightness, contrast and brightness of the surrounding environment, to determine the relationship between light and dark surfaces of buildings, increase lighting layering. Generally do not have to evenly illuminate buildings, but not noticeable spot, the dark areas in the same irradiation conditions such as uneven areas.
Floodlights should be installed as far as possible concealment or disguise, does not affect the architecture beautiful day, try to see the light but not light. The main highlight detail illuminated buildings, to make people appreciate the architectural beauty, the color of the material to see the detail, texture and texture.
Roofing appendage local cast light available components or parts of the building itself use the building verandahs, balconies, awnings and other overhangs cantilevered member and attic, architecture, etc., shading lattice facade decorative elements such as buildings, as a small volume Spotlights " hiding " for the community.
Architecture and urban space groups combined in the night in the way people evaluate the merits of a direct impact on the urban night landscape. Administrative buildings, too, should the overall space requirements of urban night departure, considering the amount of body building, appearance, color, style, materials, textures and the surrounding environment and other factors, and then depending on the characteristics of the building, to select the focus on the performance of the site, using appropriate building light the way, with a reasonable light color, shape of the building for night performance.
Administrative buildings should be dignified, concise, simple lighting theme, generally should not use colored light, colored light irradiation topical use only low saturation when necessary. In addition to the exhibit building light morphological structure of the target, light and flexible application of direct investment, indirect investment in the transmittance of light or other means.
Common building light methods are cast lighting, the translucent lighting, decorative lighting and specialty lighting, often of two or more kinds of illumination combined.
This is the basic way of building light, lighting of the overall vote (floodlit) and local cast lighting. Is to cast light mounted on the outside of a building or buildings, a building or a part of the direct exposure of the building, remodeling and building image rendering building light the way at night. Often use metal halide light source, such as high pressure sodium and LED.
To determine a good part of the illuminated surface of each façade illumination and brightness, contrast and brightness of the surrounding environment, to determine the relationship between light and dark surfaces of buildings, increase lighting layering. Generally do not have to evenly illuminate buildings, but not noticeable spot, the dark areas in the same irradiation conditions such as uneven areas.
Floodlights should be installed as far as possible concealment or disguise, does not affect the architecture beautiful day, try to see the light but not light. The main highlight detail illuminated buildings, to make people appreciate the architectural beauty, the color of the material to see the detail, texture and texture.
Roofing appendage local cast light available components or parts of the building itself use the building verandahs, balconies, awnings and other overhangs cantilevered member and attic, architecture, etc., shading lattice facade decorative elements such as buildings, as a small volume Spotlights " hiding " for the community.
Monday, December 9, 2013
What is the prospect of landscape LED light?
Landscape LED lights are integrated into the landscape lighting LED technology, which is an integral part of the modern landscape indispensable. With economic development, urban lighting more and more important, so the level of urban lighting has also been greatly improved, from the simple pursuit lights came up and the pursuit of beauty, from general light source integrated into the high-tech means to make our city the night sky increasingly bright.
LED landscape in which it plays a kind of role? Landscape LED light has different shapes, different colors and brightness of light to create a cultural atmosphere, with scenic historical and cultural, symbolic meaning harmonization and the surrounding environment. Not only for people to bring ornamental value, but also more endowed with artistic and historical value, so that people feel the breath of life in a modern city environment light color and soft, while the taste of sources of long Chinese five thousand years of history and its beautiful art form. In addition, landscape LED lights energy-saving, easy to use, rich colors, shapes and diverse, suitable for all kinds of occasions various needs.
landscape LED lights control is also more convenient. First, internal control, that is directly connected to the external power supply, the program written in the LED lamp built- IC, and each tube is numbered according to the order number be installed there, to achieve synchronization effect, not just change the time and effect. Second, external control is through the PC software to compile a good pattern, converted into binary files exist on the CF card or SD card storage devices, typically for data to be communicated directly controlled by the computer. Given so many advantages of landscape LED lights, in the future it will be the popular trends of landscape lighting.
Landscape art modern landscape lights are an indispensable part. It not only has a high ornamental itself, but also stressed that harmonization lamp landscape and scenic arts history and culture, the surrounding environment. For example, red light lantern shape Landscape bring a festive atmosphere to the square, green palm lights stand out in the school of tropical pool. Landscape applies Plaza, residential areas, public green landscape places. Be careful not to use too diverse, so overwhelming, so cluttered landscape flashy.
LED landscape in which it plays a kind of role? Landscape LED light has different shapes, different colors and brightness of light to create a cultural atmosphere, with scenic historical and cultural, symbolic meaning harmonization and the surrounding environment. Not only for people to bring ornamental value, but also more endowed with artistic and historical value, so that people feel the breath of life in a modern city environment light color and soft, while the taste of sources of long Chinese five thousand years of history and its beautiful art form. In addition, landscape LED lights energy-saving, easy to use, rich colors, shapes and diverse, suitable for all kinds of occasions various needs.
landscape LED lights control is also more convenient. First, internal control, that is directly connected to the external power supply, the program written in the LED lamp built- IC, and each tube is numbered according to the order number be installed there, to achieve synchronization effect, not just change the time and effect. Second, external control is through the PC software to compile a good pattern, converted into binary files exist on the CF card or SD card storage devices, typically for data to be communicated directly controlled by the computer. Given so many advantages of landscape LED lights, in the future it will be the popular trends of landscape lighting.
Landscape art modern landscape lights are an indispensable part. It not only has a high ornamental itself, but also stressed that harmonization lamp landscape and scenic arts history and culture, the surrounding environment. For example, red light lantern shape Landscape bring a festive atmosphere to the square, green palm lights stand out in the school of tropical pool. Landscape applies Plaza, residential areas, public green landscape places. Be careful not to use too diverse, so overwhelming, so cluttered landscape flashy.
Sunday, December 8, 2013
Osaka Universal Studios’giant Christmas colored bulbs tree sets Guinness record
According to Japan's Kyodo news agency, located in Osaka, Japan in the American movie theme park "Universal Studios Japan (USJ)" put up a giant Christmas tree up to 36 m. As a decorative lanterns hanging 356,097 largest artificial Christmas tree to get Guinness World Records certificate. Its vibrant colors so that visitors alike, Universal Studios early on immersed in a Christmas atmosphere. The Christmas tree will be on display until January 6 next year.
Christmas tree set up in the "New York area", the same day around 18:00, the tree red, blue, green and other colored bulb lit together, and every now and then fireworks in the night sky, confetti decorate outside brilliant score, creating a warm atmosphere. Christmas tree near the stage also performed a Christmas -themed show.
Japanese actress Aya Ueto lit -known attractions in Tokyo "Tokyo Midtown" Christmas colored bulbs. Christmas colored bulbs this year's theme is "the vastness of the universe." The evening of 14 November, the Japanese actress Aya Ueto and actor Kengo Kora promoting his new film "Samurai menu," lit -known attractions "Tokyo Midtown" Christmas colored bulbs.
Dating back 30 or 40 years ago, recalled how when people decorate houses with lights and trees, you'll find that most people use is a small 120 -volt incandescent bulbs. Each bulb is 5 or 10 watt bulb, with lights at night you see the same. Now, you can find these light strings, but they have not so common.
Since bulbs consume a lot of power, it generated a lot of heat. When used indoors, the heat of the three string colored bulbs (250 watts / string) produced the equivalent of 750 watts of heat generated by the space heater. The heat emitted by a single colored bulb can put things melted. They are costly. You can buy a 10 pack year mini bulbs, only about one U.S. dollar. The large bulbs may need 5-10 times more cost. One advantage of this arrangement is that a bulb failure will not affect other bulbs. This is because the system uses a 120 -volt bulb in parallel. In the 1970s it has undergone a revolution decorative light: the emergence of mini-lights on the market. Now, they have become the market leading string lights.
Christmas tree set up in the "New York area", the same day around 18:00, the tree red, blue, green and other colored bulb lit together, and every now and then fireworks in the night sky, confetti decorate outside brilliant score, creating a warm atmosphere. Christmas tree near the stage also performed a Christmas -themed show.
Japanese actress Aya Ueto lit -known attractions in Tokyo "Tokyo Midtown" Christmas colored bulbs. Christmas colored bulbs this year's theme is "the vastness of the universe." The evening of 14 November, the Japanese actress Aya Ueto and actor Kengo Kora promoting his new film "Samurai menu," lit -known attractions "Tokyo Midtown" Christmas colored bulbs.
Dating back 30 or 40 years ago, recalled how when people decorate houses with lights and trees, you'll find that most people use is a small 120 -volt incandescent bulbs. Each bulb is 5 or 10 watt bulb, with lights at night you see the same. Now, you can find these light strings, but they have not so common.
Since bulbs consume a lot of power, it generated a lot of heat. When used indoors, the heat of the three string colored bulbs (250 watts / string) produced the equivalent of 750 watts of heat generated by the space heater. The heat emitted by a single colored bulb can put things melted. They are costly. You can buy a 10 pack year mini bulbs, only about one U.S. dollar. The large bulbs may need 5-10 times more cost. One advantage of this arrangement is that a bulb failure will not affect other bulbs. This is because the system uses a 120 -volt bulb in parallel. In the 1970s it has undergone a revolution decorative light: the emergence of mini-lights on the market. Now, they have become the market leading string lights.
Thursday, December 5, 2013
What do you know about SMD ribbons?
SMD ribbon is made of FPC circuit board, LED lights, high-quality silicone casing. Waterproof, easy to use low-voltage DC power supply safety, light colors and diverse, colorful ; outdoor use can be anti- UV aging, yellowing resistance, high temperature and other advantages, which are widely used in building outline lights, entertainment quasi- decorative lighting, advertisement decoration lighting lamps fields.
Jewelry showcase lighting, display case lighting, cabinet lighting, wardrobe lighting, decorative lighting stores, lighting art lighting, advertising light box lighting and hotels, guesthouses, villas home decorative lighting.
Can be bent, can be easily fixed to unsmooth surface. Every two LED lights have a loop. Small size, rich color. High -brightness, adjustable light angle, installation, length can be customized on request. Constant current drive has low power consumption, electro-optical power close to 100 %. No UV, infrared radiation, no heat, no risk of mercury leakage.
From a global perspective, China Taiwan packaging production accounted for 60% share of the world's major companies have Everlight, Lite, Opto, Bai Hong, Wang Qi, etc., on a clear division of downstream industries, supply chain stability, especially packaging go to the mainland after the manufacturing cost of production compared to competitive advantage, the next 5-lO years, the Pearl River Delta, Yangtze River Delta, Fujian and other areas will become the world's LED packaging center.
From the mainland market, SMD ribbon domestic market a few years ago almost entirely by the United States, Japan, South Korea and Taiwan suppliers’ occupation. Although foreign firms still occupy most of the market share, but since 2000 SMD ribbon products Foshan Nationstar Optoelectronics Technology Co., Ltd. production, China will be the rapid growth of local suppliers. Now, the industry has 20-30 vendors, most enterprises are concentrated in Guangdong, Shenzhen, Dongguan, Guangzhou and Foshan, a small number of enterprises located in Jiangsu, Zhejiang and Fujian. Industry-leading companies, including the country star power in Foshan, Guangdong Hongli Opto-electronic, Shenzhen Ruifeng power, Jiangsu Wenrun good optical and photonics.
SMD ribbon packaging technology is first configured phosphor and epoxy resin, made a mold, and then with a good phosphor epoxy glue to make a pie, cake and gum paste on the chip, surrounded by then filled with epoxy resin, which is made in SMD ribbon. For example, as shown in Figure 1.
Now the market is relatively common dimensions of 50 (mm) × 50 (mm) of SMD ribbon chips inside the package has three LED epitaxial a six pin, which was soldered to the PCB circuit board surface, because it is directly with thermal glue on the surface of the cooling plate, so that the heat has been greatly improved, so that greatly improved reliability, light is also smaller.
Jewelry showcase lighting, display case lighting, cabinet lighting, wardrobe lighting, decorative lighting stores, lighting art lighting, advertising light box lighting and hotels, guesthouses, villas home decorative lighting.
Can be bent, can be easily fixed to unsmooth surface. Every two LED lights have a loop. Small size, rich color. High -brightness, adjustable light angle, installation, length can be customized on request. Constant current drive has low power consumption, electro-optical power close to 100 %. No UV, infrared radiation, no heat, no risk of mercury leakage.
From a global perspective, China Taiwan packaging production accounted for 60% share of the world's major companies have Everlight, Lite, Opto, Bai Hong, Wang Qi, etc., on a clear division of downstream industries, supply chain stability, especially packaging go to the mainland after the manufacturing cost of production compared to competitive advantage, the next 5-lO years, the Pearl River Delta, Yangtze River Delta, Fujian and other areas will become the world's LED packaging center.
From the mainland market, SMD ribbon domestic market a few years ago almost entirely by the United States, Japan, South Korea and Taiwan suppliers’ occupation. Although foreign firms still occupy most of the market share, but since 2000 SMD ribbon products Foshan Nationstar Optoelectronics Technology Co., Ltd. production, China will be the rapid growth of local suppliers. Now, the industry has 20-30 vendors, most enterprises are concentrated in Guangdong, Shenzhen, Dongguan, Guangzhou and Foshan, a small number of enterprises located in Jiangsu, Zhejiang and Fujian. Industry-leading companies, including the country star power in Foshan, Guangdong Hongli Opto-electronic, Shenzhen Ruifeng power, Jiangsu Wenrun good optical and photonics.
SMD ribbon packaging technology is first configured phosphor and epoxy resin, made a mold, and then with a good phosphor epoxy glue to make a pie, cake and gum paste on the chip, surrounded by then filled with epoxy resin, which is made in SMD ribbon. For example, as shown in Figure 1.
Now the market is relatively common dimensions of 50 (mm) × 50 (mm) of SMD ribbon chips inside the package has three LED epitaxial a six pin, which was soldered to the PCB circuit board surface, because it is directly with thermal glue on the surface of the cooling plate, so that the heat has been greatly improved, so that greatly improved reliability, light is also smaller.
Wednesday, December 4, 2013
What do you need to know about LED par can light?
LED par can lights English name is LED spotlights, it was the moment the most talked about energy saving products to the LED as a light source lamps made more and more, one of the most popular is the LED spotlights, as compared with other LED lamps ratio, lower LED par can lights prices.
LED spotlights using low voltage DC to drive: a load of small, weak interference advantages, the use of environmental requirements low. Better control of the emission spectrum of the composition, which can well, be used in museums and exhibition local or accent lighting. LED spotlights luminous point is very strong: light attenuation is much lower than traditional light sources, LED par can lights price of civilians. Response time is very fast: in the microsecond level, as long as the switch is opened, will soon light, there is no delay and flicker. To focus light emitted by a high degree of energy: concentrated in a smaller wavelength window, and high purity.
Life is very long, generally between 50,000-100,000 hours, because the LED is a semiconductor device, even frequent switching, and it will not affect the service life. LED spotlights do not add in the production process, " Mercury," and does not need inflated, no glass shell, impact resistance, shock resistance, unbreakable, easy to transport and very environmentally friendly, is called " green energy ", LED Spot price of civilians.
LED spotlights almost all concentrated in the spectrum of visible light spectrum, the luminous efficiency of up to 80 to 90 %. It is generally believed that energy-saving lamps can save energy 4 /5 is a great initiative, but also LED par can lights energy- saving lamp than 1 /4, which is a solid source greater reforms.
In addition, LED lighting also has other advantages, high quality light, essentially no radiation, LED spotlights price of civilians, typical of the green lighting; reliable and durable, very low maintenance costs, and so on. Because LED spotlights over other solid sources also have unmatched features, 10 years after the LED lighting industry will be the main source.
LED spotlights using low voltage DC to drive: a load of small, weak interference advantages, the use of environmental requirements low. Better control of the emission spectrum of the composition, which can well, be used in museums and exhibition local or accent lighting. LED spotlights luminous point is very strong: light attenuation is much lower than traditional light sources, LED par can lights price of civilians. Response time is very fast: in the microsecond level, as long as the switch is opened, will soon light, there is no delay and flicker. To focus light emitted by a high degree of energy: concentrated in a smaller wavelength window, and high purity.
Life is very long, generally between 50,000-100,000 hours, because the LED is a semiconductor device, even frequent switching, and it will not affect the service life. LED spotlights do not add in the production process, " Mercury," and does not need inflated, no glass shell, impact resistance, shock resistance, unbreakable, easy to transport and very environmentally friendly, is called " green energy ", LED Spot price of civilians.
LED spotlights almost all concentrated in the spectrum of visible light spectrum, the luminous efficiency of up to 80 to 90 %. It is generally believed that energy-saving lamps can save energy 4 /5 is a great initiative, but also LED par can lights energy- saving lamp than 1 /4, which is a solid source greater reforms.
In addition, LED lighting also has other advantages, high quality light, essentially no radiation, LED spotlights price of civilians, typical of the green lighting; reliable and durable, very low maintenance costs, and so on. Because LED spotlights over other solid sources also have unmatched features, 10 years after the LED lighting industry will be the main source.
Monday, December 2, 2013
The prospects of 18W fluorescent tubes are promising
LED manufacturers are actively increasing the output of LED lighting products, which this year has just launched a product --- 18W fluorescent tube --- has been output range. According to NPD DisplaySearch's latest report LED Lighting Market and Forecast Report, 18W fluorescent tube 2013's international market share will reach 6 %, and will rise to 22.3% by 2016. FL lamp output in 2013 will be 23,000 million, the 2016 is expected to increase to 79,100 ten thousand.
NPD DisplaySearch LED analyst Steven Sher said: "LED lighting provides innovative lighting, and effectively reduces energy consumption especially in the areas of power shortage, LED lamp will most likely be popular, and LED lighting equipment will be widely used in the world." In Japan, the United States and Europe continue to increase the output of 18W fluorescent tubes . As the market newborns, LED is clearly not the first choice of consumers.
18W fluorescent tubes are considered a green product because it does not use mercury in the manufacturing process. 18W fluorescent tubes can save 50 % power factor between 0.9-0.99 while only 0.7 T8 FL. LED lamp lives longer than T8 FL, is expected to be 5 years or 30,000 hours. 18W fluorescent tube is ideal for replacing old-fashioned lamps are used in the office or in the basement, because these areas often need 24 hours lights, energy saving is essential.
LED lamps on the issue before a greater radiation angles and color quality have been resolved. However, challenges remain, especially the problem of high cost, which has become the most important issue will be the promotion of a vintage lamp LED lamp alternatives to face in the process, because, after all, old-fashioned lamp lower prices. However, LED manufacturers are trying to narrow the price difference between the two. One way is to design a product suitable for most LED lighting power supply module.
In 2013, some of the power module manufacturers to design a new product to the MR-16, A-Lamp and LED lamps use, making the cost of these products decreased by 10%.
Sher added: "The market has already launched a number of different types of 18W fluorescent tubes, including different shapes, rated power, length, color and lighting features, but due to the lack of standard specifications, the consumer is difficult to accurately choose the most suitable. Demand for the product. "
NPD DisplaySearch LED analyst Steven Sher said: "LED lighting provides innovative lighting, and effectively reduces energy consumption especially in the areas of power shortage, LED lamp will most likely be popular, and LED lighting equipment will be widely used in the world." In Japan, the United States and Europe continue to increase the output of 18W fluorescent tubes . As the market newborns, LED is clearly not the first choice of consumers.
18W fluorescent tubes are considered a green product because it does not use mercury in the manufacturing process. 18W fluorescent tubes can save 50 % power factor between 0.9-0.99 while only 0.7 T8 FL. LED lamp lives longer than T8 FL, is expected to be 5 years or 30,000 hours. 18W fluorescent tube is ideal for replacing old-fashioned lamps are used in the office or in the basement, because these areas often need 24 hours lights, energy saving is essential.
LED lamps on the issue before a greater radiation angles and color quality have been resolved. However, challenges remain, especially the problem of high cost, which has become the most important issue will be the promotion of a vintage lamp LED lamp alternatives to face in the process, because, after all, old-fashioned lamp lower prices. However, LED manufacturers are trying to narrow the price difference between the two. One way is to design a product suitable for most LED lighting power supply module.
In 2013, some of the power module manufacturers to design a new product to the MR-16, A-Lamp and LED lamps use, making the cost of these products decreased by 10%.
Sher added: "The market has already launched a number of different types of 18W fluorescent tubes, including different shapes, rated power, length, color and lighting features, but due to the lack of standard specifications, the consumer is difficult to accurately choose the most suitable. Demand for the product. "
Sunday, December 1, 2013
Thirteen playwrights jointly write stage comedy "Motherhood Out Loud"
Recently, the company announced a new stage theater stage comedy "Mother shouted (Motherhood Out Loud)" has been put into production. It is reported that this was originally called the play "mother of the world (In Mother Words)", and was originally developed by Susan - Ross (Susan R. Rose) and Joan - Stan (Joan Stein) idea, ultimately works by ten three joint creations from American playwright.
Stage comedy "Mother shouted," by the famous director Lisa - Peterson (Lisa Peterson) featuring directed by comedian Mary - Bacon (Mary Bacon), television and theater actress Saidah Arrika Ekulona, appeared in classical musical "Les Miserables" Randy - Graf (Randy Graff), and James - Debrecen (James Lecesne), etc. Starring. Read more news on comedy.
Stage comedy "Mother shouted " premiere ceremony will be held at the Geffen Playhouse end of the year, followed by Hartford Theater (Hartford Stage) officially premiered. For the stage comedy "Mother shouted " coming soon, some professional theater critics believe that this is a totally unpredictable plays, it broke the traditional concept of people's minds of parents, using its inherent comedy elements of two generations gap between desalination. Also reveals the mother of the children most primitive emotions.
Plays published in the current creative team, Rachel Hauk as stage design, David C. Woolard is responsible for the play's costume design, lighting and sound, respectively, by the gram Christopher Kuhl and Jill BC DuBoff responsible.
It is reported that participation in the stage comedy "Mother shouted " thirteen creative writers are famous playwright playwright Leslie - Leslie Ayvazian David Cale, JJessica Goldberg, Beth Henley), Lameece Issaq, Claire LaZebnik, Lisa Loomer, Michele Lowe, "Ugly Betty " creative men Marco Pennette, Theresa - Rebeck (Theresa Rebeck), Luanne Rice, Annie Weisman and Cheryl.
Stage comedy "Mother shouted," by the famous director Lisa - Peterson (Lisa Peterson) featuring directed by comedian Mary - Bacon (Mary Bacon), television and theater actress Saidah Arrika Ekulona, appeared in classical musical "Les Miserables" Randy - Graf (Randy Graff), and James - Debrecen (James Lecesne), etc. Starring. Read more news on comedy.
Stage comedy "Mother shouted " premiere ceremony will be held at the Geffen Playhouse end of the year, followed by Hartford Theater (Hartford Stage) officially premiered. For the stage comedy "Mother shouted " coming soon, some professional theater critics believe that this is a totally unpredictable plays, it broke the traditional concept of people's minds of parents, using its inherent comedy elements of two generations gap between desalination. Also reveals the mother of the children most primitive emotions.
Plays published in the current creative team, Rachel Hauk as stage design, David C. Woolard is responsible for the play's costume design, lighting and sound, respectively, by the gram Christopher Kuhl and Jill BC DuBoff responsible.
It is reported that participation in the stage comedy "Mother shouted " thirteen creative writers are famous playwright playwright Leslie - Leslie Ayvazian David Cale, JJessica Goldberg, Beth Henley), Lameece Issaq, Claire LaZebnik, Lisa Loomer, Michele Lowe, "Ugly Betty " creative men Marco Pennette, Theresa - Rebeck (Theresa Rebeck), Luanne Rice, Annie Weisman and Cheryl.
Thursday, November 28, 2013
Home LED lighting penetration rate expected to reach 30% in Japan
Japan is already the world's leading country with the lowest power consumption of American families are two -fold evenly Japanese family, instrumentation four times, but was not satisfied with this meaning in Japan, the Japanese in the future to produce at low cost many areas of the world to compete with developing countries, can be said to have no chance of winning, so the development of the " environment" related industries, is consistent with the direction of Japanese entrepreneurs.
Japan's economy based on industrial province intend, look forward to in 2030, so that LED / OLED bulb replacement for at least 60% of the incandescent light bulb, of course, the most important family is still occupied by fluorescent lighting high luminous efficacy and a better economic advantage, However fluorescent grow skills have peaked, while the luminous efficiency of LED / OLED is still the continuous growth of output, but down 90 % of the cost of each track for 10 years, at least a measure of this trend can be continuously 2016, therefore, the future luminous efficacy home LED lighting according to the source, is expected to continuously increase ( and thus its utilization will be broader and more power), but the price will be reduced to an appropriate stage.
Japan and the United States, Europe and other LED light source manufacturer believes that the current luminous efficiency of individual commercial home LED lighting, although only 80 lumens / watt, but 3 or 4 years 120 to 150 lumens / watt high-efficiency LED lights will be commercialized, then the entire application life products the total cost of the application cycle (light bulbs expense plus electricity) will be lower than the energy saving LED light bulbs. LED lamp manufacturers to guess the future to reach 200 to 300 lm / W in 2020 will be able to match the goal.
Japan's machinery industry based on a combination would guess, when in 2030, LED / Ohome LED lighting indoor lighting penetration rate in Japan will reach 30%, representing 20% of total electricity for lighting, in terms of energy saving and carbon reduction benefits, will be thrifty 18.7 billion kwh of electricity for the year, or 7 million tons of carbon dioxide emissions.
Home LED lighting optimistic vision, however, can not neglect the development of another new generation of lighting technology, discrete components that Ohome LED lighting, OLED organic light-emitting diode that is seen as the next generation continuation display technology.
Japan's economy based on industrial province intend, look forward to in 2030, so that LED / OLED bulb replacement for at least 60% of the incandescent light bulb, of course, the most important family is still occupied by fluorescent lighting high luminous efficacy and a better economic advantage, However fluorescent grow skills have peaked, while the luminous efficiency of LED / OLED is still the continuous growth of output, but down 90 % of the cost of each track for 10 years, at least a measure of this trend can be continuously 2016, therefore, the future luminous efficacy home LED lighting according to the source, is expected to continuously increase ( and thus its utilization will be broader and more power), but the price will be reduced to an appropriate stage.
Japan and the United States, Europe and other LED light source manufacturer believes that the current luminous efficiency of individual commercial home LED lighting, although only 80 lumens / watt, but 3 or 4 years 120 to 150 lumens / watt high-efficiency LED lights will be commercialized, then the entire application life products the total cost of the application cycle (light bulbs expense plus electricity) will be lower than the energy saving LED light bulbs. LED lamp manufacturers to guess the future to reach 200 to 300 lm / W in 2020 will be able to match the goal.
Japan's machinery industry based on a combination would guess, when in 2030, LED / Ohome LED lighting indoor lighting penetration rate in Japan will reach 30%, representing 20% of total electricity for lighting, in terms of energy saving and carbon reduction benefits, will be thrifty 18.7 billion kwh of electricity for the year, or 7 million tons of carbon dioxide emissions.
Home LED lighting optimistic vision, however, can not neglect the development of another new generation of lighting technology, discrete components that Ohome LED lighting, OLED organic light-emitting diode that is seen as the next generation continuation display technology.
Wednesday, November 27, 2013
Put this slim rechargeable torch lighting into your purse
Recently, an American company to launch a credit card sized Orange Slice thin torch lighting White Slice. The LED product with a credit card the same shape, the thickness of the product model is about 0.10 inches, the thickness of the finished product is not expected to produce more than 0.105 inches.
In general, the thickness of a credit card is about 0.05 inches, so the White Slice thickness equivalent to only two credit cards. It uses high power density lithium polymer batteries, integrated circuits and 10 high-output LED. According to the specifications of torch lighting, White Slice luminous flux is of up to 15 lumens, 30 lumens and 45 lumens.
White Slice LED driver circuitry automatically adjusts the voltage to extend battery life and keep the brightness. When the battery is low, LED will start flashing to alert the user to charge again. Previously there have been the easiest card light switch is faulty. White Slice uses two switches, just in case. Further, in the production process, the printed circuit board is immersed in the liquid gold, so that the switch is gilded. Gold has a strong resistance to corrosion, so you can be assured White Slice switch.
In addition, based on the White Slice, Orange Slice Company has designed the Green Slice. Compared with White Slice, Green Slice thinner, LED halve the number ( 5 ), and therefore the brightness by half, working hours extended twice. On the choice of shell material, Orange Slice also different attempts, there is used a light -weight carbon fibers, but also has great rigidity easily processed using a polyacetal copolymer.
Torch lighting can use high-quality NiMH or NiCd batteries recommended genuine GP, gen, etc. This section uses energy-efficient LED bulbs, low power consumption, the use of more environmentally friendly rechargeable batteries. Charging the battery voltage is 1.2V alkaline batteries 1.5V, high-quality rechargeable battery internal resistance lower than alkaline batteries can provide enough power for passing current, please be assured of high quality genuine nickel-metal hydride rechargeable batteries.
In general, the thickness of a credit card is about 0.05 inches, so the White Slice thickness equivalent to only two credit cards. It uses high power density lithium polymer batteries, integrated circuits and 10 high-output LED. According to the specifications of torch lighting, White Slice luminous flux is of up to 15 lumens, 30 lumens and 45 lumens.White Slice LED driver circuitry automatically adjusts the voltage to extend battery life and keep the brightness. When the battery is low, LED will start flashing to alert the user to charge again. Previously there have been the easiest card light switch is faulty. White Slice uses two switches, just in case. Further, in the production process, the printed circuit board is immersed in the liquid gold, so that the switch is gilded. Gold has a strong resistance to corrosion, so you can be assured White Slice switch.
In addition, based on the White Slice, Orange Slice Company has designed the Green Slice. Compared with White Slice, Green Slice thinner, LED halve the number ( 5 ), and therefore the brightness by half, working hours extended twice. On the choice of shell material, Orange Slice also different attempts, there is used a light -weight carbon fibers, but also has great rigidity easily processed using a polyacetal copolymer.
Torch lighting can use high-quality NiMH or NiCd batteries recommended genuine GP, gen, etc. This section uses energy-efficient LED bulbs, low power consumption, the use of more environmentally friendly rechargeable batteries. Charging the battery voltage is 1.2V alkaline batteries 1.5V, high-quality rechargeable battery internal resistance lower than alkaline batteries can provide enough power for passing current, please be assured of high quality genuine nickel-metal hydride rechargeable batteries.
Tuesday, November 26, 2013
North Korea Lighting Exhibition attracts numerous visitors
Korea National Exhibition lighting and can light fixture equipment and technology will be published on the 19th to the 20th at the industrial complex at the University Kinzer, on display at the various power LED lights and large LED screens and other exhibits pocketed the participant 's eye.
According to the Korean Central News Agency reported that the DPRK National Exhibition can light fixture and lighting equipment and technology will be published on the 19th to the 20th at the industrial complex at the University Kinzer, on display at the various power LED lights and large LED screens and other exhibits pocketed the participants the eyeball.
Reported that the can light fixture engineering sector production units, scientific and educational institutions and technology workers, teachers, etc. come to the meeting. Kim Il Sung University, Kinzer industrial university, lighting Pyongyang launched more than 110 kinds of plants and other units of more than 400 pieces of LED lamps and other lighting sources and stabilizer, published dozens of papers.
Participants exchanged for the realization of can light fixture equipment and modernization of production technology and scientific, to make the city beautiful night, monumental buildings and people's cultural entertainment lighting technology problem solving achievements and experience.
The report also said the DPRK National Academy of Sciences Institute of Power Machinery, three thousand lighting fixtures factory, Taedong River Technology Agency focus type exhibited efficient LED flood light illumination, a variety of power LED lights and large LED screens and other exhibits pocketed the participants the eyeball.
From indoor to outdoor, and more to adorn the surroundings, modern lighting fixtures design style more diverse, classical, modern, stylish, Continental, American, fresh, luxurious, beautiful. This requires indoor lighting companies have sufficient foresight and innovation, according to the changing needs of consumers to design consumer satisfaction. Lighting not only played household lighting effects, different styles can be embellished different effects.
Spot lighting to create an atmosphere of space. Generally, we can be a ceiling as the main light source, set the lamp, or LED lights trough small spotlights, downlights and other decorative or as a focus of the lighting, to reduce indoor light and dark contrast. If we have the habit of reading in bed, it is recommended to put a dimmable bedside directly shaped lamp, energy-saving lamps installed halogen lamp or cold, to avoid eyestrain.
According to the Korean Central News Agency reported that the DPRK National Exhibition can light fixture and lighting equipment and technology will be published on the 19th to the 20th at the industrial complex at the University Kinzer, on display at the various power LED lights and large LED screens and other exhibits pocketed the participants the eyeball.
Reported that the can light fixture engineering sector production units, scientific and educational institutions and technology workers, teachers, etc. come to the meeting. Kim Il Sung University, Kinzer industrial university, lighting Pyongyang launched more than 110 kinds of plants and other units of more than 400 pieces of LED lamps and other lighting sources and stabilizer, published dozens of papers.
Participants exchanged for the realization of can light fixture equipment and modernization of production technology and scientific, to make the city beautiful night, monumental buildings and people's cultural entertainment lighting technology problem solving achievements and experience.
The report also said the DPRK National Academy of Sciences Institute of Power Machinery, three thousand lighting fixtures factory, Taedong River Technology Agency focus type exhibited efficient LED flood light illumination, a variety of power LED lights and large LED screens and other exhibits pocketed the participants the eyeball.
From indoor to outdoor, and more to adorn the surroundings, modern lighting fixtures design style more diverse, classical, modern, stylish, Continental, American, fresh, luxurious, beautiful. This requires indoor lighting companies have sufficient foresight and innovation, according to the changing needs of consumers to design consumer satisfaction. Lighting not only played household lighting effects, different styles can be embellished different effects.
Spot lighting to create an atmosphere of space. Generally, we can be a ceiling as the main light source, set the lamp, or LED lights trough small spotlights, downlights and other decorative or as a focus of the lighting, to reduce indoor light and dark contrast. If we have the habit of reading in bed, it is recommended to put a dimmable bedside directly shaped lamp, energy-saving lamps installed halogen lamp or cold, to avoid eyestrain.
Monday, November 25, 2013
Philips introduces a new generation of compact spiral energy saving bulbs
The emergence of the Apple iPod allows music to bring more fashionable colors. Now, Philips unique aesthetic lines of the new spiral energy saving bulbs in the international design world gained high recognition for your life and add a sense of fashion.
Following the October 1, 2013, the world's authoritative industrial design in Japan Industrial Design Promotion Organization (JIDPO) Philips Mini Spiral CFL issued after the G-Mark Design Award; recently, the family obtained a 2013China'sMostSuccessfulDesignsAward.
Now, more and more families choose energy-saving lamps for illumination of choice. Following the Philips Mini Spiral CFL successful listing, Philips has launched a compact spiral energy saving bulb, the product brings more space curve modeling beauty, but also the continuation of the mini spiral energy saving light " small size " advantage; not only cold, warm colors optional, and there are 15 W / 20 W / 24 W 3 sizes to choose from. In the case to achieve the same brightness, compact spiral energy saving bulb can reach the equivalent 75 W / 100 W / 120 watt ordinary incandescent lighting effects. Thus, the use of compact spiral energy saving lamp can save 4 /5 of the electricity.
In addition to the home environment, offices, shopping malls and other public places are to play a delicate spiral CFL expertise places. And smaller, more refined, faster startup; it appears, lets hope the "energy" and "beautiful" consumers have been satisfied with the new choice.
Compact Spiral energy saving lamps have long life of 6000 hours; using unique rare earth dichromatic phosphor technology in use after 2000 hours and still be able to maintain just 85% of the brightness when used; compared with the same wattage energy saving U-tube brightness increased by 10%; higher color, light color pleasing to the eye and comfortable. This means that a clearer and enjoyable to read and carry out other activities.
With compact small size Spiral energy saving bulbs will replace incandescent, not only to meet the needs of decoration, but also to save about 80 % of the lighting power consumption and effective way. It will also be home to promote or business owners improve lighting quality, save electricity costs, cost-effective choice.
Spiral appearance attractive enough; actual performance of the electricity savings; Philips compact spiral energy saving lamp energy saving lamp will declare the "bright" era.
Following the October 1, 2013, the world's authoritative industrial design in Japan Industrial Design Promotion Organization (JIDPO) Philips Mini Spiral CFL issued after the G-Mark Design Award; recently, the family obtained a 2013China'sMostSuccessfulDesignsAward.
Now, more and more families choose energy-saving lamps for illumination of choice. Following the Philips Mini Spiral CFL successful listing, Philips has launched a compact spiral energy saving bulb, the product brings more space curve modeling beauty, but also the continuation of the mini spiral energy saving light " small size " advantage; not only cold, warm colors optional, and there are 15 W / 20 W / 24 W 3 sizes to choose from. In the case to achieve the same brightness, compact spiral energy saving bulb can reach the equivalent 75 W / 100 W / 120 watt ordinary incandescent lighting effects. Thus, the use of compact spiral energy saving lamp can save 4 /5 of the electricity.
In addition to the home environment, offices, shopping malls and other public places are to play a delicate spiral CFL expertise places. And smaller, more refined, faster startup; it appears, lets hope the "energy" and "beautiful" consumers have been satisfied with the new choice.
Compact Spiral energy saving lamps have long life of 6000 hours; using unique rare earth dichromatic phosphor technology in use after 2000 hours and still be able to maintain just 85% of the brightness when used; compared with the same wattage energy saving U-tube brightness increased by 10%; higher color, light color pleasing to the eye and comfortable. This means that a clearer and enjoyable to read and carry out other activities.
With compact small size Spiral energy saving bulbs will replace incandescent, not only to meet the needs of decoration, but also to save about 80 % of the lighting power consumption and effective way. It will also be home to promote or business owners improve lighting quality, save electricity costs, cost-effective choice.
Spiral appearance attractive enough; actual performance of the electricity savings; Philips compact spiral energy saving lamp energy saving lamp will declare the "bright" era.
Wednesday, November 20, 2013
PwC plans to invest $ 1 billion to aquire management consulting company Booz
One of the big four accounting firm Deloitte & Touche (Deloitte) acquired bankruptcy protection management consulting firm Monitor (Monitor), the other one of the four members of the PricewaterhouseCoopers (PwC) has also launched M & Management Consulting the pace of business.
Yesterday, PricewaterhouseCoopers and Booz & Company (Booz & Company) jointly announced that they have signed a conditional agreement to merge. The transaction is subject to the consent of Booz & Company partner, regulatory approvals and other customary closing conditions fulfilled. Although no formal merger transaction prices disclosed, but there are foreign media speculation that the transaction amount may be $ 1 billion. Read more news on management consulting.
Booz & Company CEO Mathis (Cesare R. Mainardi) publicly stated: "Our goal is to help customers discover and build their winning capabilities needed to differentiate the two sides could not just make this innovative combined value proposition be achieved, also in the next one century remodeling the management consulting industry. "
PricewaterhouseCoopers International Limited, Global Chairman Dai Ruili (Dennis Nally), said: "We believe that the existing audit, consulting and tax services possible merger with Booz & Company, will create an outstanding professional services organization serving more provide first-class customer service. "
Booz & Company 's 300 man- year partnership agreement in December of the vote, and in the end publicly further instructions. Under the merger agreement the contents of the merged PricewaterhouseCoopers after Bos will give up their name, the name of the PwC commenced business operations.
Founded in 1914, Booz & Company, in 2013 VAULT management consulting company ranked fourth on the list, which earlier this year acquired the headquarters in Dusseldorf, Germany, a global consulting firm - out of a corporate management consulting company. At that time, its Greater China president Bai Xinhui (Sarah Butler) once told reporters: "The Company and the company to expand capacity expansion needs, the management consulting industry in recent years, mergers and acquisitions wave erection of two reasons."
"The whole industry is in the integration process." An international consulting industry veteran Jiang Bo ( a pseudonym ) told reporters that the first echelon of the international management consulting industry is MBB ( McKinsey, Boston, Bain ), the second tier is Kearney, Boss, Roland Berger, but medium-sized management consulting firm will be more volatile performance pressure, because the scale is not enough, the business of a single species management consulting company for the maintenance of a customer's cost more.
Yesterday, PricewaterhouseCoopers and Booz & Company (Booz & Company) jointly announced that they have signed a conditional agreement to merge. The transaction is subject to the consent of Booz & Company partner, regulatory approvals and other customary closing conditions fulfilled. Although no formal merger transaction prices disclosed, but there are foreign media speculation that the transaction amount may be $ 1 billion. Read more news on management consulting.
Booz & Company CEO Mathis (Cesare R. Mainardi) publicly stated: "Our goal is to help customers discover and build their winning capabilities needed to differentiate the two sides could not just make this innovative combined value proposition be achieved, also in the next one century remodeling the management consulting industry. "
PricewaterhouseCoopers International Limited, Global Chairman Dai Ruili (Dennis Nally), said: "We believe that the existing audit, consulting and tax services possible merger with Booz & Company, will create an outstanding professional services organization serving more provide first-class customer service. "
Booz & Company 's 300 man- year partnership agreement in December of the vote, and in the end publicly further instructions. Under the merger agreement the contents of the merged PricewaterhouseCoopers after Bos will give up their name, the name of the PwC commenced business operations.
Founded in 1914, Booz & Company, in 2013 VAULT management consulting company ranked fourth on the list, which earlier this year acquired the headquarters in Dusseldorf, Germany, a global consulting firm - out of a corporate management consulting company. At that time, its Greater China president Bai Xinhui (Sarah Butler) once told reporters: "The Company and the company to expand capacity expansion needs, the management consulting industry in recent years, mergers and acquisitions wave erection of two reasons."
"The whole industry is in the integration process." An international consulting industry veteran Jiang Bo ( a pseudonym ) told reporters that the first echelon of the international management consulting industry is MBB ( McKinsey, Boston, Bain ), the second tier is Kearney, Boss, Roland Berger, but medium-sized management consulting firm will be more volatile performance pressure, because the scale is not enough, the business of a single species management consulting company for the maintenance of a customer's cost more.
Tuesday, November 19, 2013
Everlight launches new series of blue LED light strips
Global leader in LED packaging manufacturer Everlight August 26 announced, with 30 years of professional experience in research and development of LED assembly, continued to expand 3020 package size products, the introduction of new low-power 45-21S 0.2W lighting components. This new component can be widely used in all kinds of general lighting; especially blue LED light strip light products can be more cost effective.
Everlight 45-21S Standard 3020 is an upgraded version of package size, because of the special package designs, to have the best cooling effect, 60mA current drive, the luminous efficiency can reach 115lm / W ( cool white ) and 104lm / W ( warm white ). 45-21S features a combination of these products, is one hundred million light most cost-effective products that provides general lighting best solution for playing pieces of plans to reduce the number of LED application products is very suitable, such as blue LED light strips, panel lights, etc.
Traditional lights are used 20mA PLCC package products, it must by many LED quantity, densely arranged regularly, such as fluorescent tubes only show like glow. Therefore, the recent market trends show, the blue LED light strip ( article ) manufacturers want to reduce overall manufacturing costs, but to play in reducing the number of parts LED premise, but also to maintain the original, or even higher brightness. 45-21S Everlight to meet user expectations are, without changes in the design of the circuit and the PCB board, an increase in the brightness of the original PLCC package, the original can be large current drive LED package, the LED simultaneously reduced the number of playing pieces, and the Lamp (Article) drivers will be more cost-effective.
Everlight 45-21S Series ANSI color temperature from 2700K to 6500K, CRI > 80, at 60mA current, standard output flux 20lm ( warm white ) and 22lm ( cold white ); at 75mA current, the value of 24 lumens -26lm. 45-21S as a lead-free process and RoHS environmental standards, and have passed the LM80 testing.
Everlight 45-21S Standard 3020 is an upgraded version of package size, because of the special package designs, to have the best cooling effect, 60mA current drive, the luminous efficiency can reach 115lm / W ( cool white ) and 104lm / W ( warm white ). 45-21S features a combination of these products, is one hundred million light most cost-effective products that provides general lighting best solution for playing pieces of plans to reduce the number of LED application products is very suitable, such as blue LED light strips, panel lights, etc.
Traditional lights are used 20mA PLCC package products, it must by many LED quantity, densely arranged regularly, such as fluorescent tubes only show like glow. Therefore, the recent market trends show, the blue LED light strip ( article ) manufacturers want to reduce overall manufacturing costs, but to play in reducing the number of parts LED premise, but also to maintain the original, or even higher brightness. 45-21S Everlight to meet user expectations are, without changes in the design of the circuit and the PCB board, an increase in the brightness of the original PLCC package, the original can be large current drive LED package, the LED simultaneously reduced the number of playing pieces, and the Lamp (Article) drivers will be more cost-effective.
Everlight 45-21S Series ANSI color temperature from 2700K to 6500K, CRI > 80, at 60mA current, standard output flux 20lm ( warm white ) and 22lm ( cold white ); at 75mA current, the value of 24 lumens -26lm. 45-21S as a lead-free process and RoHS environmental standards, and have passed the LM80 testing.
Monday, November 18, 2013
Philips introduces high performance DC lamp Lumileds
Recently, Philips Lumileds' LUXEON Rebel LED UL approved to become the first high-performance DC lamp. Now, through the use of LUXEON Rebel LED, the new products are expected to solid state lighting applications faster and more easily selected Underwriters Laboratories (UL) certification directory.
UL certified lighting products in the United States de facto mandatory, because the major agencies are required to pass this certification, including municipal authorities, government agencies, architects and insurance companies. This certification can make use of LUXEON Rebel without making a new DC lamp assembly through a comprehensive internal investigation can be UL Listed, thus speeding up the speed to market. As lamps must be UL Listed to be eligible to use ENERGY STAR label, which will also contribute through this certification ENERGY STAR certification.
In addition, to obtain UL certification can promote the use of a class of power, thereby helping to improve street lighting and other LED applications, the performance of LUXEON Rebel lens cover meet UL standards for electrical requirements, as before without UL through comprehensive research; past full requirements have hampered research on more efficient use of class 1 power supply.
Philips Lumileds' Application director Rudi Hechfellner said, "the majority of products sold in the U.S. state lighting manufacturers are asked to join the UL certification catalog, but until now, the certification process is very confusing. By using LUXEON Rebel, engineers can according to the UL clear guidance work, shorten UL review cycle, avoiding the luminaries certification process unexpected problems that may arise. "
UL certified lighting products in the United States de facto mandatory, because the major agencies are required to pass this certification, including municipal authorities, government agencies, architects and insurance companies. This certification can make use of LUXEON Rebel without making a new DC lamp assembly through a comprehensive internal investigation can be UL Listed, thus speeding up the speed to market. As lamps must be UL Listed to be eligible to use ENERGY STAR label, which will also contribute through this certification ENERGY STAR certification.
In addition, to obtain UL certification can promote the use of a class of power, thereby helping to improve street lighting and other LED applications, the performance of LUXEON Rebel lens cover meet UL standards for electrical requirements, as before without UL through comprehensive research; past full requirements have hampered research on more efficient use of class 1 power supply.
Philips Lumileds' Application director Rudi Hechfellner said, "the majority of products sold in the U.S. state lighting manufacturers are asked to join the UL certification catalog, but until now, the certification process is very confusing. By using LUXEON Rebel, engineers can according to the UL clear guidance work, shorten UL review cycle, avoiding the luminaries certification process unexpected problems that may arise. "
Sunday, November 17, 2013
Bluetooth speakers can be a perfect Christmas gift
Today's smart phones are already a handheld computer. Take watching movies and listening to music can be said to be, when we facing a large screen mobile phone to watch movies or listen to music, there is always an indescribable depression.
Many people will feel mobile sound enough to force, if there is loud and clear detailed sound, it must considerably. Bluetooth speakers will be able to lift this repression. Bluetooth wireless technology, fast and convenient connections smartphone or tablet. Pick up bluetooth speaker on okbuynow for Christmas gift.
Bluetooth speakers are better able to carry on with the portable intelligent terminal equipment connection, so portable applications designed for outdoor products are very popular. With integrated structural design, small size, and the design of hand-carry, outdoor full range of children.
In fact, from the volume portable positioning point of view, be placed in the living room environment is also suitable for use, so the overall appearance is very focused sense of design, while requiring fashion sense. Has a red, white and black version, there is no problem with the home environment.
In general, the process of connecting Bluetooth speakers are relatively complicated, but simplify this process, the key aspect is the control number, try to simplify operation. Case is designed with three buttons at the top of the front, adjust the volume, respectively, and Bluetooth / mute button, the button beneath the lights, the control panel is very simple.
It feature wireless Bluetooth connection and support those product that have Bluetooth functions, such as, mobile, Tablet PC, and laptop. It's also support Line in audio input. Hands-free multifunction speaker is specially design for safety driving. With voice prompt function and it can mostly connect with two phones at the same time. Fashionable and transparent shell, smooth touch, small and convenient to carry, multifunction integrated design, it provides you with premium perfect sound quality. You can enjoy the excellent sound quality while at home, traveling or in business work.
Many people will feel mobile sound enough to force, if there is loud and clear detailed sound, it must considerably. Bluetooth speakers will be able to lift this repression. Bluetooth wireless technology, fast and convenient connections smartphone or tablet. Pick up bluetooth speaker on okbuynow for Christmas gift.
Bluetooth speakers are better able to carry on with the portable intelligent terminal equipment connection, so portable applications designed for outdoor products are very popular. With integrated structural design, small size, and the design of hand-carry, outdoor full range of children.
In fact, from the volume portable positioning point of view, be placed in the living room environment is also suitable for use, so the overall appearance is very focused sense of design, while requiring fashion sense. Has a red, white and black version, there is no problem with the home environment.
In general, the process of connecting Bluetooth speakers are relatively complicated, but simplify this process, the key aspect is the control number, try to simplify operation. Case is designed with three buttons at the top of the front, adjust the volume, respectively, and Bluetooth / mute button, the button beneath the lights, the control panel is very simple.
It feature wireless Bluetooth connection and support those product that have Bluetooth functions, such as, mobile, Tablet PC, and laptop. It's also support Line in audio input. Hands-free multifunction speaker is specially design for safety driving. With voice prompt function and it can mostly connect with two phones at the same time. Fashionable and transparent shell, smooth touch, small and convenient to carry, multifunction integrated design, it provides you with premium perfect sound quality. You can enjoy the excellent sound quality while at home, traveling or in business work.
Thursday, November 14, 2013
2014 U.S. Fluorescent Lighting Fair
Time: April 23 - 25, 2014
Hall: Las Vegas
Address: Las Vegas, USA
Organizer: Illuminating Engineering Society of North America and the International Association of Lighting Design
Info:
2014 American International Lighting Fair, is North America's most important about the architectural and commercial lighting exhibition event. The exhibition by the Illuminating Engineering Society of North America and the International Association of Lighting Design, has been successfully held 21 sessions in New York and Las Vegas organized tour, since 2012 New York Jacob K. Javits Exhibition Centre Extension, so the exhibition moves to Philadelphia, Pennsylvania Convention Center. 2010 The exhibition in Las Vegas Exhibition Centre, the exhibition area of 14,000 square meters, attracted participants from all over the world more than 470 exhibitors, exhibition covers more than 1,500 fluorescent light tube products, up to more than 19,000 professional visitors people are from international and U.S. domestic architecture, lighting, engineering, various other aspects of the design unit 's top professionals. Many well-known companies are exhibiting year after year, and in the exhibition occupies a significant position.
It is held in conjunction with LIGHTFAIR INTERNATIONAL along with the world's largest architectural and commercial fluorescent light tube to the theme of a seminar for international lighting manufacturers to provide a showcase of new products, raise awareness, promote new technologies and services, demonstration and application software, and effective solution technical problems a great place; also for exhibitors and merchants to provide opportunities for interaction between, so that we experience the new products, new designs, new technologies and services to new ideas, but also makes the exhibitors can be kept informed of today's lighting industry trends.
Exhibits:
Ballasts, drivers, converters; coating, polishing and related materials; daylight fluorescent light tube products; design and analysis software; optical and remote lighting, fluorescent light tube, incandescent, landscape lights, bollard lights and fountain lights; Downlights, wall lighting fixtures, motion lights; open light, sensors, controllers and control software; industrial Lighting; rail lighting, low voltage cables, reflective concave groove, surface fixtures; architectural lighting integrated systems, lighting components, decorative candlesticks, chandeliers and pendants; lamps and work lights; entrance cue lights and emergency lights; outdoor lamps, HID lamps; lamp; LED lights; special lighting and equipment, stage lights and entertainment, publishing and related industry publications, anti-breaking and industrial special lights.
Hall: Las Vegas
Address: Las Vegas, USA
Organizer: Illuminating Engineering Society of North America and the International Association of Lighting Design
Info:
2014 American International Lighting Fair, is North America's most important about the architectural and commercial lighting exhibition event. The exhibition by the Illuminating Engineering Society of North America and the International Association of Lighting Design, has been successfully held 21 sessions in New York and Las Vegas organized tour, since 2012 New York Jacob K. Javits Exhibition Centre Extension, so the exhibition moves to Philadelphia, Pennsylvania Convention Center. 2010 The exhibition in Las Vegas Exhibition Centre, the exhibition area of 14,000 square meters, attracted participants from all over the world more than 470 exhibitors, exhibition covers more than 1,500 fluorescent light tube products, up to more than 19,000 professional visitors people are from international and U.S. domestic architecture, lighting, engineering, various other aspects of the design unit 's top professionals. Many well-known companies are exhibiting year after year, and in the exhibition occupies a significant position.
It is held in conjunction with LIGHTFAIR INTERNATIONAL along with the world's largest architectural and commercial fluorescent light tube to the theme of a seminar for international lighting manufacturers to provide a showcase of new products, raise awareness, promote new technologies and services, demonstration and application software, and effective solution technical problems a great place; also for exhibitors and merchants to provide opportunities for interaction between, so that we experience the new products, new designs, new technologies and services to new ideas, but also makes the exhibitors can be kept informed of today's lighting industry trends.
Exhibits:
Ballasts, drivers, converters; coating, polishing and related materials; daylight fluorescent light tube products; design and analysis software; optical and remote lighting, fluorescent light tube, incandescent, landscape lights, bollard lights and fountain lights; Downlights, wall lighting fixtures, motion lights; open light, sensors, controllers and control software; industrial Lighting; rail lighting, low voltage cables, reflective concave groove, surface fixtures; architectural lighting integrated systems, lighting components, decorative candlesticks, chandeliers and pendants; lamps and work lights; entrance cue lights and emergency lights; outdoor lamps, HID lamps; lamp; LED lights; special lighting and equipment, stage lights and entertainment, publishing and related industry publications, anti-breaking and industrial special lights.
Wednesday, November 13, 2013
USDA: Australia's 2013/14 wheat production is down to 23.5 million tons
USDA: Australia's 2013/14 wheat production
is down to 23.5 million tons
According to the U.S. Department of
Agriculture Foreign Agricultural Service
Center released the latest Counselor report shows that 2013/14 ( October to
September ) Australian wheat production may be 23.5 million tons, down from an
earlier forecast of 24.5 million tons, higher than the 2012 / 13 year 's 22.1
million tons.
Counsellor expected 2013/14 Australian
wheat export volume of 18 million tons, compared with an earlier forecast of
18.5 million tons last year to 19.5 million tons. Where food, seed and
industrial use is projected at 300 million tons, the earlier forecast of 3.3
million tons, last year 320 million tons.
Counsellor expected 2013/14 Australian
wheat ending stocks at 280 million tons, compared with an earlier forecast of
300 million tons last year to 3.2 million tons.
According to the U.S. Department of
Agriculture Foreign Agricultural Service Center released the latest Counselor
report shows that 2013/ 14 year (November to October) Australian barley
production forecast unchanged at 7.2 million tons. By contrast, last year's
actual production of 670 million tons.
Counsellor expected 2013/14 Australian
barley exports to 400 million tones, consistent with earlier forecasts; last
year was 380 million tons.
2013/14 ending stocks of barley in
Australia is estimated at 369,000 tons, down from an earlier forecast of
410,000 tons, last year was 21.9 million tons.
Senator Richard Colbeck has announced that
Australia's aquaculture industry has been significantly increased and now
accounts for almost half of the country’s fish production. Australian Bureau of Agricultural Resource
Economics and Science of the “Australian Fisheries Statistics 2012 annual report” shows that in the past decade
aquaculture fishery products in Australia, the share of revenue from 30% to
46%.
"Most of the growth can be attributed
to the rapid growth of the fish farming industry in 2011-2012, the production
of farmed salmon to become the largest groups of species, its revenue grew 20
percent and it is still Australia's highest yielding fishery products, worth $
513 million, " Mr baker, Cole said.
Colbeck Members said the report shows that
Australia’s total
fisheries production value growth of 3 percent to $ 2.3 billion. Australia's
domestic seafood consumption in the past 30 years has been on the rise,
Australians eat 25 kilograms per person per year seafood, higher than the world
average.
Tuesday, November 12, 2013
TE Connectivity introduced several new bulb base for a wide range of LED series
Darmstadt, Germany, December 14, 2012 - TE Connectivity (TE), as a global technology leader, today announced the launch of a series of innovative and scalable solderless LED series bulb bases, to meet the most common LED series connectivity requirements.
TE solderless LED lamp with a small, thin, and flexibility characteristics for the onboard chip series LED offers convenient solderless connections. Both low cost and simple design provides reliable power required LED connections, mechanical attachment and reliable heat retention. TE bulb base weld solve many of the problems, the use of standard screws can be directly connected to the LED heat sink, this design is more reliable, easier to use, and accelerate speed to market. TE holder Easy installation saves time; improve the reliability and quality, while greatly reducing the product installation time.
TE Intelligent Buildings Division, Global Product Manager Bart Broeren said: "The current market demand for on-board chip LED growing increasingly rich product selection. TE lamp will continue to expand the scope of application solutions for the specific needs of customers on the LED, provide a more intelligent, better and more convenient products. Scalable design bulb bases focus on the future, through these flexible, scalable bulb base sets, allows current and future advanced LED products to get faster application. "
TE lamp is not only easy to use, while the design of robust, reliable and feature-rich. Currently, TE has announced the availability of 24 different models LED lamp series, including the highly flexible modular rectangular connectors and fit easily assembled sections of monolithic LED size configuration preloaded connector. At the same time, customers can choose additional spring metal temperature; increase the filling pressure of the heat sink, the thermal interface material is not subject to a variety of ceramic substrate damage, but the design of the molded case to reduce the obstruction of the LED light output. TE characteristics having a high reflectance, and rounded white lighting materials can be avoided to the maximum extent the generation of shadows. Optical isolation zone is secondary optics provides a clear projection area.
TE Connectivity is a global company with annual sales of $ 13 billion. Company designs and manufactures approximately 500,000 kinds of products that connect and protect the various products we use every day in the power and data flow. From consumer electronics, energy and healthcare, to automotive, aerospace and communication networks, we use smarter, faster, and more sophisticated technology, giving the product more likely.
TE solderless LED lamp with a small, thin, and flexibility characteristics for the onboard chip series LED offers convenient solderless connections. Both low cost and simple design provides reliable power required LED connections, mechanical attachment and reliable heat retention. TE bulb base weld solve many of the problems, the use of standard screws can be directly connected to the LED heat sink, this design is more reliable, easier to use, and accelerate speed to market. TE holder Easy installation saves time; improve the reliability and quality, while greatly reducing the product installation time.
TE Intelligent Buildings Division, Global Product Manager Bart Broeren said: "The current market demand for on-board chip LED growing increasingly rich product selection. TE lamp will continue to expand the scope of application solutions for the specific needs of customers on the LED, provide a more intelligent, better and more convenient products. Scalable design bulb bases focus on the future, through these flexible, scalable bulb base sets, allows current and future advanced LED products to get faster application. "
TE lamp is not only easy to use, while the design of robust, reliable and feature-rich. Currently, TE has announced the availability of 24 different models LED lamp series, including the highly flexible modular rectangular connectors and fit easily assembled sections of monolithic LED size configuration preloaded connector. At the same time, customers can choose additional spring metal temperature; increase the filling pressure of the heat sink, the thermal interface material is not subject to a variety of ceramic substrate damage, but the design of the molded case to reduce the obstruction of the LED light output. TE characteristics having a high reflectance, and rounded white lighting materials can be avoided to the maximum extent the generation of shadows. Optical isolation zone is secondary optics provides a clear projection area.
TE Connectivity is a global company with annual sales of $ 13 billion. Company designs and manufactures approximately 500,000 kinds of products that connect and protect the various products we use every day in the power and data flow. From consumer electronics, energy and healthcare, to automotive, aerospace and communication networks, we use smarter, faster, and more sophisticated technology, giving the product more likely.
Subscribe to:
Posts (Atom)